AUDI R8 II
4.2 FSI quattro,
AUDI
Autod
Kaubavedu
Mootorrattad
ALFA ROMEO
AUDI
BMW
CADILLAC
CHEVROLET
CHRYSLER
CITROËN
DACIA
DAEWOO
DAF
DAIHATSU
DODGE
FIAT
FORD
GAZ
GMC
GREAT WALL
HONDA
HUMMER
HYUNDAI
INFINITI
ISUZU
IVECO
JAGUAR
JEEP
KIA
LADA
LAND ROVER
LEXUS
MAZDA
MERCEDES-BENZ
MG
MINI
MITSUBISHI
NISSAN
OPEL
PEUGEOT
PONTIAC
PORSCHE
RENAULT
RENAULT TRUCKS
ROVER
SAAB
SEAT
SKODA
SMART
SSANGYONG
SUBARU
SUZUKI
TESLA
TOYOTA
VOLVO
VW
ZAZ
R8 II
4.2 FSI quattro
Minu garaaž
Lisage lemmikutesse
Minu garaaž
Empty

AUDI R8 II, Convertible, 10-15, , (427, 429)

AUDI R8 II, Convertible, 10-15, , (427, 429)

General data
General basic values :
Timing chain Type of engine control
8 Number of spark plugs/glow plugs required
1-5-4-8-6-3-7-2 Firing sequence
1,50 Minimum engine oil pressure when idling (Test temperature 80° C )
0,100 Maximum deformation of cylinder head
139,50 Minimum cylinder head height
92,80 Stroke
84,50 Bore
4 Valves per cylinder
12,50 Compression ratio
10,00 - 14,00 Compression pressure (Difference max. 3 bar ) [new engine ]
Cooling system :
1,60 - 2,00 Cooling system pressure (radiator cap opening pressure)
80° Thermostat opens at temperature
Fuel system
Fuel system in general :
OTTO 98 ROZ Type of fuel
Direct injection Mixture processing designation
Exhaust gas test values
General exhaust-gas-relevant values :
The diagnostic socket is at the lower edge of the dashboard on the driver's side. Diagnostic socket location
Chassis data
Chassis settings :
-1°00'+0°15'-0°15' Camber rear [PR. - number 1BL ]
0°20'+0°10'-0°10' Toe-in rear [Test value ]
19°04'+0°10'-0°10' Wheel steering angle outer wheel (relative steering angle) [PR. - number 1BL ]
20°00'+0°00'-0°00' Wheel steering angle inner wheel (relative steering angle)
-1°00'+0°10'-0°10' Camber front [PR. - number 1BL ]
0°20'+0°08'-0°08' Toe-in front (total toe) [Test value ]
Vehicle ready for operation with spare wheel, tools, accessories and full tank. Conditions for axle measurement
Chassis dimensions :
2650 Wheel base
1595 Tread front
1633 Tread rear
Wheel rims and tyres :
0,00 Front tyre pressure (see B column left )
0,00 Rear tyre pressure (see B column left )
Brake system
Brake dimensions :
38,00 Front axle brake disc thickness [Ceramic brake disc ]
32,40 Front axle brake disc thickness wear limit
17,00 Front axle brake lining thickness [with backing plate ]
9,50 Front axle brake lining thickness wear limit [Ceramic brake disc, with backing plate ]
28,00 Rear axle brake disc thickness [Ceramic brake disc ]
30,40 Rear axle brake disc thickness wear limit
9,00 Rear axle brake lining thickness [Parking brake, with backing plate ]
9,00 Rear axle brake lining thickness wear limit [Ceramic brake disc, with backing plate ]
380,00 Front axle brake disc diameter [Ceramic brake disc ]
356,00 Rear axle brake disc diameter [Ceramic brake disc ]
Engine tightening torques
Cylinder head :
35 Nm Cylinder head screws (Replace sealing ring(s). ) [Screw(s) 6, Cap, 06 stage ]
9 Nm Valve cover (set)
8 Nm + 90° Camshaft bearing (Tighten new screws in inside-to-outside order. ) [Bearing cap ]
Engine control :
9 Nm Timing case cover 2. cylinder row
9 Nm Timing case cover 1. cylinder row
22 Nm Bottom part of control unit housing (Tighten cross-wise. ) [M8 ]
80 Nm + 90° Inlet camshaft wheel (Use new screw. )
80 Nm + 90° Outlet camshaft wheel (Use new screw. )
5 Nm + 90° Timing chain tensioner intermediate shaft (Use new screw(s). )
5 Nm + 90° Camshaft timing chain tensioner (Use new screw(s). )
Auxiliary assemblies :
22 Nm Accessory drive belt tensioning device
22 Nm Accessory drive belt deflection pulley
46 Nm Holder - generator [M10 ]
25 Nm Air-conditioning compressor
23 Nm Alternator
Engine lubrication :
25 Nm Oil filter housing [Oil filter cover ]
22 Nm Oil drain plug(s) [12-point screw(s) ]
Engine management :
20 Nm Knock sensor
10 Nm Camshaft sensor
55 Nm Lambda sensor
Ignition system :
30 Nm Spark plugs
Carburetion :
9 Nm Fuel-distributing pipe
40 Nm Pressure-tube connection
10 Nm Injection pump [High-pressure pump ]
Fuel supply :
25 Nm Fuel line [High-pressure side ]
Air intake system :
11 Nm Intake manifold
Exhaust system :
25 Nm Exhaust manifold (Use new nut(s). ) [Lower nuts ]
Cooling system :
9 Nm Coolant pump
Engine block :
60 Nm + 90° Flywheel (Use new screw(s). )
Start system :
65 Nm Starter
Power transmission tightening torques
Clutch :
8 Nm + 180° Clutch pressure plate (Use new screws and tighten them crosswise. )
10 Nm Clutch slave cylinder [02 stage ]
Differential :
30 Nm Differential oil control screw (Oil filler screw(s) ) [front ]
Gearbox lubrication :
50 Nm Gearbox oil drain plug
50 Nm Gearbox oil filler plug
Axle drive :
200 Nm + 180° Front axle drive shaft (Use new screw(s). ) [Central bolt ]
Suspension front tightening torques
Wheels/tires :
120 Nm Wheel attachment
Front axle brake :
110 Nm Front axle brake caliper
12 Nm Brake hose [at the brake caliper ]
16 Nm Brake line [at brake hose ]
9 Nm Front axle brake disc (Use new screw(s). )
8 Nm Wheel speed sensor
Front axle suspension :
110 Nm Suspension strut (Use new nut(s). ) [at the transverse control arm ]
28 Nm Shock-absorber piston rod
Front axle wheel suspension :
110 Nm Front axle upper transverse control arm (Use new nut(s). ) [on stub axle ]
110 Nm Track control arm, front wheel, lower (Use new nut(s). ) [on stub axle ]
60 Nm Front axle stabiliser support at axle control arm
60 Nm Front axle stabiliser support at stabiliser
30 Nm Front axle stabilizer mount at subframe
200 Nm + 180° Wheel hub/front axle wheel bearing (Use new screw. ) [Central bolt ]
200 Nm + 180° Front axle drive shaft (Use new screw(s). ) [Central bolt ]
Front axle steering :
50 Nm Track rod end on track rod
100 Nm Track rod on steering gear
110 Nm Track rod end on stub axle
Suspension rear tightening torques
Wheels/tires :
120 Nm Wheel attachment
Rear axle brake :
55 Nm Rear axle brake caliper (Use new screw(s). ) [Parking brake ]
9 Nm Rear axle brake disc (Use new screw(s). )
Rear axle suspension :
110 Nm Rear axle suspension strut (Use new nut(s). ) [on stub axle ]
28 Nm Rear axle shock-absorber piston rod
Rear axle wheel suspension :
110 Nm Track control arm, rear axle, upper (Use new nut(s). ) [on stub axle ]
110 Nm Track control arm, rear axle, lower (Use new nut(s). ) [on stub axle ]
200 Nm + 180° Wheel hub/rear axle wheel bearing (Use new screw. ) [Central bolt ]
60 Nm Rear axle stabiliser support at stabiliser
110 Nm Rear axle stabiliser support at stub axle (Use new nut(s). )
Rear axle steering :
110 Nm Rear axle track rod (Use new nut(s). ) [on stub axle ]
Consumables
Filling quantities and specifications :
10,00 Engine oil with filter
VW 501 14 Brake fluid specification
630 - 670 Air-conditioning system refrigerant
R134a Refrigerant specification
140 - 160 Air-conditioning system oil [Compressor Denso 7SEU17 ]
G 052 300 A2 Air-conditioning compressor oil specification (Original oil ) [Compressor Denso 7SEU17 ]
75 Tank capacity
G 004 000 M2 Hydraulic transmission fluid specification (Original oil )
1,40 Front axle differential oil [Amount to change ]
G 052 145 A1 Front axle oil specification (Original oil )
0,90 Hydraulic gear shift fluid [with automated shift gearbox ]
Change intervals
For service data :
after 3 years for the first time, then every 2 years Brake fluid change interval
Tüüp:
Convertible ► 10-15 (427, 429)
KBA: 7967 AAP
Mootor:
4.2 (CNDA)
Võimsus:
316 KW / 430 HP
Maht:
4163 cm Petrol
Veoskeem:
Täielik ►
Kütus:
Bensiin
Spetsifikatsioonid:
10,00 litres
Engine oil with filter
1-5-4-8-6-3-7-2
Firing sequence
1,40 litres
Front axle differential oil
G 052 145 A1
Front axle oil specification
0,00 bar
Front tyre pressure
0,00 bar
Rear tyre pressure
-1°00'+0°10'-0°10'
Camber front
-1°00'+0°15'-0°15'
Camber rear
2650 mm
Wheel base
Lisateave (156) ►
Vedrustus, pehmendus
Lukustusseade
Lisaülekanne
Turvasüsteemid

car-mod.com