AUDI A6 IV Allroad
TDI quattro,
2012-pr.
2010
2011
2012
2013
2014
2015
2016
2017
2018
2019
2000
2001
2002
2003
2004
2005
2006
2007
2008
2009
1990
1991
1992
1993
1994
1995
1996
1997
1998
1999
1980
1981
1982
1983
1984
1985
1986
1987
1988
1989
AUDI
Autod
Kaubavedu
Mootorrattad
ALFA ROMEO
AUDI
BMW
CADILLAC
CHEVROLET
CHRYSLER
CITROËN
DACIA
DAEWOO
DAF
DAIHATSU
DODGE
FIAT
FORD
GAZ
GMC
GREAT WALL
HONDA
HUMMER
HYUNDAI
INFINITI
ISUZU
IVECO
JAGUAR
JEEP
KIA
LADA
LAND ROVER
LEXUS
MAZDA
MERCEDES-BENZ
MG
MINI
MITSUBISHI
NISSAN
OPEL
PEUGEOT
PONTIAC
PORSCHE
RENAULT
RENAULT TRUCKS
ROVER
SAAB
SEAT
SKODA
SMART
SSANGYONG
SUBARU
SUZUKI
TESLA
TOYOTA
VOLVO
VW
ZAZ
A6 IV Allroad
TDI quattro

AUDI A6 IV Allroad, Estate, 12-pr., CGQB

AUDI A6 IV Allroad, Estate, 12-pr., CGQB

General data
General basic values :
Timing chain Type of engine control
91,40 Stroke
83,00 Bore
4 Valves per cylinder
Hydraulic tappets Compensation for valve play
6 Number of spark plugs/glow plugs required
1-4-3-6-2-5 Firing sequence
28,00 - 33,00 Compression pressure (Difference max. 5 bar ) [new engine ]
16,80 Compression ratio
0,100 Maximum deformation of cylinder head (Rework of the cylinder head is not allowed. )
1,80 Minimum engine oil pressure when idling (Test temperature 80° C )
Fuel system
Fuel system in general :
Diesel Type of fuel
Common Rail Mixture processing designation
Exhaust gas test values
General exhaust-gas-relevant values :
The diagnostic socket is at the lower edge of the dashboard on the driver's side. Diagnostic socket location
Chassis data
Chassis settings :
-1°20'+0°25'-0°25' Camber rear (maximum difference between left and right 0°30' )
0°20'+0°10'-0°10' Toe-in rear (Maximum variation in vehicle longitudinal direction 10' )
18°11'+0°30'-0°30' Wheel steering angle outer wheel (relative steering angle)
20°00'+0°00'-0°00' Wheel steering angle inner wheel (relative steering angle)
-1°20'+0°25'-0°25' Camber front (maximum difference between left and right 0°30' ) [PR. - number 1BY ]
0°20'+0°10'-0°10' Toe-in front (total toe) [Setting ]
Prior to axle measurement and using an appropriate diagnostic tester, move the vehicle into a position simulating the vehicle's empty weight. Conditions for axle measurement (Allocation of PR. no. before vehicle measuring. ) [with air suspension ]
Wheel rims and tyres :
0,00 Rear tyre pressure (see sticker on the inside of the driver's door )
0,00 Front tyre pressure (see sticker on the inside of the driver's door )
Chassis dimensions :
2905 Wheel base
1631 Tread front
1596 Tread rear
Engine tightening torques
Engine mounting :
90 Nm + 180° Subframe (Use new screw(s). ) [M12 x 35 ]
40 Nm Engine bracket [on the engine block ]
55 Nm Engine mounting [at subframe ]
20 Nm + 90° Torque arm (Use new screw(s). )
30 Nm Torque support holder
Auxiliary assemblies :
25 Nm Air-conditioning compressor pressure line [M8 ]
40 Nm Air-conditioning compressor holder
25 Nm Air-conditioning compressor
40 Nm Holder - generator
20 Nm Alternator
23 Nm Accessory drive belt deflection pulley
50 Nm + 90° Accessory drive belt tensioning device (Use new screw(s). )
Start system :
30 Nm + 90° Starter (Use new screw(s). ) [M12 ]
Engine block :
20 Nm + 90° Vibration damper (Use new screw(s). )
60 Nm + 90° Drive plate (Use new screw(s). ) [on crankshaft ]
60 Nm Flywheel (Use new screw(s). ) [to drive plate ]
50 Nm + 180° Main bearing [02 stage ]
35 Nm + 90° Connecting rod bearing (Use new screw(s). )
Engine control :
90° Timing case cover [Screw(s) 5 - 24, 05 stage ]
8 Nm + 90° Timing case cover 2. cylinder row [02 stage ]
8 Nm + 90° Timing case cover 1. cylinder row [02 stage ]
23 Nm Toothed belt tensioning roller (Use new screw(s). ) [Toothed belt - high pressure pump ]
Cylinder head :
8 Nm + 90° Valve cover (set) [02 stage ]
90° Cylinder head screws [05 stage ]
9 Nm Camshaft bearing [02 stage ]
Engine lubrication :
8 Nm + 90° Oil pump (Use new screw(s). )
30 Nm Oil drain plug(s)
9 Nm Oil filter housing [on the engine block ]
35 Nm Oil sump [Oil sump top part, Locking screw ]
Cooling system :
3 Nm + 90° Coolant pump (Gradually tighten screws crosswise. )
23 Nm Coolant pump pulley
Air intake system :
9 Nm Intake manifold
Exhaust system :
30 Nm + 90° Exhaust manifold (Use new screw(s) with hot screw paste. ) [at turbocharger ]
23 Nm Diesel particulate filter (Use new nut(s) with hot screw paste. )
23 Nm Exhaust pipe (Use new screw(s). )
Charging :
23 Nm Turbo charger (Use new screw(s) with hot screw paste. )
Engine management :
17 Nm Glow plugs
9 Nm Crankshaft sensor
9 Nm Camshaft sensor
55 Nm Lambda sensor
45 Nm Exhaust gas temperature sensor
Carburetion :
14 Nm Injection nozzle/injector [Retaining clamp ]
25 Nm Injection hoses
25 Nm High-pressure line
22 Nm Fuel-distributing pipe
70 Nm High-pressure pump pulley [central nut ]
22 Nm High-pressure pump
Power transmission tightening torques
Axle drive :
20 Nm Propeller shaft intermediate bearing
20 Nm Drive shaft heat protection plate [rear axle ]
24 Nm Propeller shaft heat protection plate
Gearbox lubrication :
12 Nm Gearbox oil drain plug (Use new screw. ) [Gearbox 0BK ]
30 Nm Gearbox oil filler plug (Use new screw. ) [Gearbox 0BK ]
27 Nm Distributor gearbox oil filler screw (Use new screw. ) [Gearbox 0BK ]
12 Nm Distributor gearbox oil drain plug (Use new screw. ) [Gearbox 0BK ]
Differential :
27 Nm Differential oil control screw (Use new screw. ) [Gearbox 0BK ]
10 Nm Differential oil drain plug (Use new screw. ) [Gearbox 0BK ]
Gearbox mounting :
40 Nm Gearbox support [At the gearbox ]
20 Nm Gearbox mounting [at the crossmember ]
70 Nm Gearbox support [Property class 10.9, M10 x 40 ]
Gearbox :
30 Nm + 90° Gearbox flange connection at engine (Reuse screws only 2 times. ) [M12 ]
Suspension front tightening torques
Front axle wheel suspension :
40 Nm Front axle support joint at stub axle (Use new screw(s). )
140 Nm Lower rear front axle transverse control arm (Use new nut(s). ) [on stub axle ]
20 Nm Front suspension cross-brace
Front axle steering :
80 Nm Track rod end on track rod
100 Nm Track rod on steering gear
Suspension rear tightening torques
Rear axle wheel suspension :
25 Nm + 90° Rear axle stabiliser mounting (Use new screw(s). ) [at subframe ]
Consumables
Filling quantities and specifications :
4,35 Manual gearbox oil [Direct gearbox 0B5 ]
6,00 Oil for twin clutch (Manufacturer's specification 5,5 - 6,0 litres ) [Direct gearbox 0B5, Amount to change ]
G 052 529 A2 Twin clutch oil specification (Original oil ) [Direct gearbox 0B5 ]
0,95 Rear axle differential oil [0BF axle drive ]
G 052 145 A1 Rear axle oil specification (Original oil )
TL 774 G Cooling fluid specification
12,00 Coolant
0,85 Oil for control unit in rear axle differential gear [0BF axle drive ]
G 052 515 A2 Oil specification for control unit in rear axle differential gear (Use original oil ) [0BF axle drive ]
G 055 532 A2 Manual gearbox oil specification (Original oil ) [Direct gearbox 0B5 ]
3,60 Automatic gearbox oil (Manufacturer's specification 3,6 - 4,0 litres ) [Gearbox 0BK, Amount to change ]
G 060 162 A2 Automatic gearbox oil specification (Original oil ) [Gearbox 0BK ]
0,90 Front axle differential oil [Gearbox 0BK, Amount to change ]
G 052 145 A1 Front axle oil specification (Original oil ) [Gearbox 0BK ]
0,80 Transfer case oil [Gearbox 0BK, Amount to change ]
G 055 145 A2 Transfer case specification (Original oil ) [Gearbox 0BK ]
VW 507 00 Engine oil specification
6,40 Engine oil with filter
1,00 Brake fluid when changing
VW 501 14 Brake fluid specification
Lighting
Internal light sources :
LED Footwell light (Original part )
Front light sources :
LED Surround light (Original part )
Change intervals
For service data :
every 60.000 km Fuel filter change interval
every 60.000 km Air filter change interval
first time at 180.000 km, then every 30.000 km Ash saturation level check interval
after 3 years for the first time, then every 2 years Brake fluid change interval
Tüüp:Estate ► 12-pr.
KBA: 0588 ATZ
Mootor: 3.0 (CGQB)
Võimsus:230 KW / 313 HP
Maht: 2967 cm Diesel
Veoskeem: Täielik ►
Kütus:Diiselmootor
Spetsifikatsioonid:
6,40 litres Engine oil with filter
VW 507 00 Engine oil specification
4,35 litres Manual gearbox oil
G 055 532 A2 Manual gearbox oil specification
3,60 litres Automatic gearbox oil
G 060 162 A2 Automatic gearbox oil specification
1-4-3-6-2-5 Firing sequence
12,00 litres Coolant
0,90 litres Front axle differential oil
G 052 145 A1 Front axle oil specification
0,95 litres Rear axle differential oil
G 052 145 A1 Rear axle oil specification
0,00 bar Front tyre pressure
0,00 bar Rear tyre pressure
1,00 litres Brake fluid when changing
-1°20'+0°25'-0°25' Camber front
-1°20'+0°25'-0°25' Camber rear
2905 mm Wheel base
TL 774 G Cooling fluid specification
Lisateave (154) ►
Sidur, ehitusosad
Käigukast
Lukustusseade

car-mod.com