AUDI TT II
TFSI quattro,
2008-2010
2010
2011
2012
2013
2014
2015
2016
2017
2018
2019
2000
2001
2002
2003
2004
2005
2006
2007
2008
2009
1990
1991
1992
1993
1994
1995
1996
1997
1998
1999
1980
1981
1982
1983
1984
1985
1986
1987
1988
1989
AUDI
Autod
Kaubavedu
Mootorrattad
ALFA ROMEO
AUDI
BMW
CADILLAC
CHEVROLET
CHRYSLER
CITROËN
DACIA
DAEWOO
DAF
DAIHATSU
DODGE
FIAT
FORD
GAZ
GMC
GREAT WALL
HONDA
HUMMER
HYUNDAI
INFINITI
ISUZU
IVECO
JAGUAR
JEEP
KIA
LADA
LAND ROVER
LEXUS
MAZDA
MERCEDES-BENZ
MG
MINI
MITSUBISHI
NISSAN
OPEL
PEUGEOT
PONTIAC
PORSCHE
RENAULT
RENAULT TRUCKS
ROVER
SAAB
SEAT
SKODA
SMART
SSANGYONG
SUBARU
SUZUKI
TESLA
TOYOTA
VOLVO
VW
ZAZ
TT II
TFSI quattro

AUDI TT II, Convertible, 08-10, CCZA

AUDI TT II, Convertible, 08-10, CCZA

General data
General basic values :
Timing chain Type of engine control
4 Number of spark plugs/glow plugs required
5100 Speed at maximum performance
1700 Speed at maximum torque
280 Maximum torque
92,80 Stroke
82,50 Bore
4 Valves per cylinder
Hydraulic tappets Compensation for valve play
45° Inlet valve seat angle
45° Outlet valve seat angle
5,970 - 5,990 Inlet valve stem diameter
5,950 - 5,970 Outlet valve stem diameter
1-3-4-2 Firing sequence
9,60 Compression ratio
1,20 Minimum engine oil pressure when idling (Test temperature 80° C )
0,050 Maximum deformation of cylinder head
11,00 - 14,00 Compression pressure (Difference max. 3 bar ) [new engine ]
Belt info
General dimensions :
21,36 x 1117 Accessory drive belt size
Fuel system
Fuel system in general :
OTTO 95 ROZ Type of fuel (Loss in power ) [Alternative possibility: ]
3,00 - 6,00 System pressure (in front of high-pressure pump )
7,80 Fuel consumption
Exhaust gas test values
General exhaust-gas-relevant values :
80 Minimum engine oil temperature at VET
660 - 860 Idling speed with manual gearbox
Petrol exhaust gas values :
0,97 - 1,03 Lambda value
660 - 860 Test speed for lambda sensor signal
wideband sensor Lambda sensor design
2500 - 3000 Petrol conditioning speed
120 Petrol conditioning time
0,00 - 0,20 CO content at increased idling
2500 - 3000 Increased idling speed
0,00 - 0,50 CO content at idling
Chassis data
Chassis settings :
0°10'+0°10'-0°10' Toe-in front (total toe)
Vehicle ready for operation with spare wheel, tools, accessories and full tank. Conditions for axle measurement
-0°41'+0°30'-0°30' Camber front (maximum difference between left and right 0°30' )
20°00'+0°00'-0°00' Wheel steering angle inner wheel (relative steering angle)
18°40'+0°20'-0°20' Wheel steering angle outer wheel (relative steering angle) [PR. - number 1BD ]
0°25'+0°10'-0°10' Toe-in rear (Maximum variation in vehicle longitudinal direction 10' )
-1°20'+0°30'-0°30' Camber rear (maximum difference between left and right 0°30' )
Chassis dimensions :
1558 Tread rear
1572 Tread front
2467 Wheel base
Wheel rims and tyres :
0,00 Rear tyre pressure (see B column left )
0,00 Front tyre pressure (see B column left )
Brake system
Brake dimensions :
14,00 Front axle brake lining thickness [without backing plate ]
57,00 Front axle brake piston diameter [Brake caliper FNR-G57 ]
12,00 Rear axle brake lining thickness [without backing plate ]
41,00 Rear axle brake piston diameter
310,00 Rear axle brake disc diameter [Internally ventilated brake discs ]
340,00 Front axle brake disc diameter [Brake caliper FNR-G57, PR. - number 1LK, PR. - number 1LM ]
2,00 Rear axle brake lining thickness wear limit [without backing plate ]
2,00 Front axle brake lining thickness wear limit [without backing plate ]
19,00 Rear axle brake disc thickness wear limit [Internally ventilated brake discs ]
22,00 Rear axle brake disc thickness [Internally ventilated brake discs ]
27,00 Front axle brake disc thickness wear limit [Brake caliper FNR-G57, PR. - number 1LK, PR. - number 1LM ]
30,00 Front axle brake disc thickness [Brake caliper FNR-G57, PR. - number 1LK, PR. - number 1LM ]
Engine tightening torques
Auxiliary assemblies :
25 Nm Air-conditioning compressor pressure line
10 Nm Accessory drive belt tensioning device
9 Nm Vacuum pump
20 Nm + 90° Air-conditioning compressor holder
25 Nm Air-conditioning compressor
20 Nm + 90° Holder - generator
23 Nm Alternator
Exhaust system :
23 Nm Exhaust pipe holder
40 Nm Exhaust pipe (Use new nut(s). )
25 Nm Exhaust manifold [04 stage ]
Engine management :
55 Nm Lambda sensor (Use hot screw paste )
4,5 Nm Crankshaft sensor
5 Nm Charge air pressure sensor
9 Nm Camshaft sensor
20 Nm Knock sensor
Fuel supply :
1,5 Nm Fuel filter holder
20 Nm Fuel line [High-pressure side ]
Charging :
10 Nm Charge air pipes
Engine control :
20 Nm Balance shaft timing chain tension rail
20 Nm Camshaft timing chain tensioning rail
20 Nm Camshaft timing chain slip rail
20 Nm Balance shaft timing chain guide rail
9 Nm Top part of control unit housing (Tighten cross-wise. )
8 Nm + 45° Bottom part of control unit housing (Use new screws and tighten them crosswise. )
65 Nm Drive chain – balance shaft chain tensioner
9 Nm Camshaft timing chain tensioner
25 Nm + 90° Intermediate shaft chain sprocket [03 stage ]
9 Nm Oil pump drive chain tensioner
9 Nm Toothed belt guard [Coolant pump ]
20 Nm + 90° Camshaft adjuster (Use new screw. ) [Exhaust side, M8, Central bolt ]
Start system :
40 Nm Starter
Engine mounting :
70 Nm + 90° Subframe (Use new screw(s). ) [on chassis ]
100 Nm + 90° Torque arm (Use new screw(s). ) [at subframe ]
20 Nm + 90° Engine mounting (Use new screw(s). ) [Strut ]
40 Nm + 180° Engine bracket (Use new screw(s). ) [on the engine block ]
Engine block :
150 Nm + 90° Crankshaft central screw (Use new screw. )
20 Nm + 90° Main bearing (Use new screw(s). ) [Lateral screw-fitting ]
45 Nm + 90° Connecting rod bearing (Use new screw(s). )
9 Nm Balance shaft gear wheel [on the engine block ]
60 Nm + 90° Flywheel (Use new screw(s). )
Cylinder head :
8 Nm + 90° Valve cover (set) (Tighten new screws in inside-to-outside order. ) [Bearing casing ]
8 Nm + 90° Cylinder head screws (Use new screw(s). ) [with variable valve control, Screw(s) 11, 04 stage ]
Engine lubrication :
8 Nm + 45° Oil sump (Tighten new bolts helically in outside to inside order. ) [Oil sump lower part ]
30 Nm Oil drain plug(s)
9 Nm Oil pump
23 Nm Oil cooler
Cooling system :
9 Nm Coolant pump (Tighten cross-wise. )
10 Nm + 90° Drive wheel for coolant pump (Use new screw. (left-hand thread) )
Ignition system :
30 Nm Spark plugs
Air intake system :
9 Nm Intake manifold
Carburetion :
20 Nm High-pressure pump
Power transmission tightening torques
Gear shifting :
90° Selector cable linkage [02 stage ]
Gearbox :
80 Nm Gearbox flange connection at engine [M12 ]
Transfer case :
45° Flange connection, transfer box onto transmission [02 stage ]
40 Nm Bracket - transfer box [At the gearbox, 03 stage ]
Gearbox lubrication :
60 Nm Distributor gearbox oil drain plug
15 Nm Distributor gearbox oil filler screw
20 Nm Gearbox oil filter cover
3 Nm Gearbox oil drain plug [Direct gearbox 02E, Overflow pipe ]
15 Nm Oil control screw(s)
Axle drive :
25 Nm Drive shaft heat protection plate
25 Nm Propeller shaft intermediate bearing
30 Nm All-wheel clutch oil drain plug
15 Nm All-wheel clutch oil control screw
Gearbox mounting :
90° Gearbox support [At the gearbox, 02 stage ]
90° Gearbox mounting [at gearbox holder, 02 stage ]
Differential :
15 Nm Rear axle differential oil control screw
Clutch :
20 Nm Clutch pressure plate (Gradually tighten screws crosswise. ) [M7 ]
Suspension front tightening torques
Front axle brake :
8 Nm Wheel speed sensor
15 Nm Bleed valve [Brake caliper FNR-G57 ]
30 Nm Front axle brake caliper
200 Nm Front axle brake caliper mounting support (Use new screw(s). )
4 Nm Front axle brake disc
14 Nm Brake hose [Brake caliper FNR-G57 ]
12 Nm Brake line [Brake caliper FN3 ]
Front axle wheel suspension :
65 Nm Front axle stabiliser support at stabiliser (Use new nut(s). )
65 Nm Front axle stabiliser support at suspension strut (Use new nut(s). )
20 Nm + 90° Front axle stabilizer mount at subframe (Use new screw(s). )
40 Nm + 45° Front axle support joint at transverse control arm (Use new nut(s). )
20 Nm + 90° Front axle support joint at stub axle (Use new nut(s). )
70 Nm + 90° Front axle transverse control arm (Use new screw(s). ) [Bearing pedestal, on chassis ]
200 Nm + 180° Wheel hub/front axle wheel bearing (Use new screw. ) [without ribbing, Central bolt, Bi-hexagon ]
Wheels/tires :
120 Nm Wheel attachment
8 Nm Tyre pressure sensor(s) [Union nut(s) ]
Front axle steering :
50 Nm + 90° Steering gear (Use new screw(s). )
20 Nm + 90° Track rod end on stub axle (Use new nut(s). )
20 Nm + 90° Lower steering column joint (Use new screw(s). )
100 Nm Track rod on steering gear
50 Nm Track rod end on track rod
Front axle suspension :
70 Nm + 90° Suspension strut (Use new screw(s) and nut(s). ) [on stub axle ]
60 Nm Shock-absorber piston rod (Use new nut(s). )
Suspension rear tightening torques
Rear axle brake :
10 Nm Rear axle bleeder valve
14 Nm Rear axle brake hose
35 Nm Rear axle brake caliper (Use new screw(s). )
90 Nm + 90° Rear axle brake caliper mounting support (Use new screw(s). )
Rear axle wheel suspension :
90° Panhard rod(s), rear axle [02 stage ]
25 Nm Rear axle stabiliser support at stub axle
40 Nm Rear axle stabiliser support at stabiliser
25 Nm + 90° Rear axle stabiliser mounting (Use new screw(s). )
90 Nm + 45° Rear axle longitudinal control arm (Use new screw(s). ) [on stub axle ]
90 Nm + 90° Rear axle carrier (Use new screw(s). ) [on chassis ]
90 Nm + 90° Track control arm, rear axle, lower (Use new screw(s) and nut(s). ) [on stub axle ]
130 Nm + 90° Track control arm, rear axle, upper (Use new screw(s) and nut(s). ) [on stub axle ]
200 Nm + 180° Wheel hub/rear axle wheel bearing (Use new screw. ) [without ribbing, Central bolt, Bi-hexagon ]
Rear axle suspension :
180 Nm Rear axle shock-absorber [on stub axle ]
25 Nm Rear axle shock-absorber piston rod (Use new nut(s). )
Rear axle steering :
130 Nm + 90° Rear axle track rod (Use new screw(s) and nut(s). ) [on stub axle ]
Wheels/tires :
120 Nm Wheel attachment
8 Nm Tyre pressure sensor(s) [Union nut(s) ]
Electrical system
General electrical system :
12 Battery voltage
Consumables
Filling quantities and specifications :
VW 503 01|VW 504 00 Engine oil specification [Longlife ]
6,90 Manual gearbox oil [Direct gearbox 02E, New filling ]
G 052 182 A2 Manual gearbox oil specification (Original oil ) [Direct gearbox 02E ]
4,60 Engine oil with filter
G 052 145 A1 Rear axle oil specification (Original oil )
0,70 All-wheel drive clutch oil [Amount to change ]
0,95 Rear axle differential oil
0,90 Transfer case oil
DOT 4 Brake fluid specification
55 Tank capacity
TL 774 G Cooling fluid specification
9,50 Coolant
G 052 145 A1 Transfer case specification (Original oil )
Change intervals
For service data :
after 3 years for the first time, then every 2 years Brake fluid change interval
every 30.000 km / 2 years Interior filter change interval
every 90.000 km / 6 years Spark plug change interval
every 60.000 km Transmission oil change interval [Direct gearbox 02E ]
every 90.000 km Air filter change interval
Tüüp:Convertible ► 08-10
KBA: 8307 ABD
Mootor: 2.0 (CCZA)
Võimsus:147 KW / 200 HP
Maht: 1984 cm Petrol
Veoskeem: Täielik ►
Kütus:Bensiin
Spetsifikatsioonid:
4,60 litres Engine oil with filter
VW 503 01|VW 504 00 Engine oil specification
6,90 litres Manual gearbox oil
G 052 182 A2 Manual gearbox oil specification
1-3-4-2 Firing sequence
9,50 litres Coolant
0,95 litres Rear axle differential oil
G 052 145 A1 Rear axle oil specification
0,00 bar Front tyre pressure
0,00 bar Rear tyre pressure
every 90.000 km / 6 years Spark plug change interval
660 - 860 1/min Idling speed with manual gearbox
-0°41'+0°30'-0°30' Camber front
-1°20'+0°30'-0°30' Camber rear
2467 mm Wheel base
TL 774 G Cooling fluid specification
Lisateave (256) ►
Rattad, rehvid
Lisad
Lukustusseade
Turvasüsteemid
Suruõhusüsteem

car-mod.com